Why the Widespan Gate Is a No-Damage Option
If you need to block a wide opening but want to avoid drilling into walls, the Regalo Widespan Extra Wide Baby Gate (Model #1158) is designed around a pressure-mount system. That means it stays in place by pressing against the doorframe or wall surfaces, rather than relying on screws or brackets. For renters or anyone who prefers not to patch holes later, this is a practical choice.
The gate also features an easy-to-use lever handle with a one-touch release safety lock, so adults can open it quickly while still keeping the barrier secure. Before you start, it's worth confirming that your opening matches the gate's width range—the catalog doesn't specify exact dimensions, so measure your opening first.
Step-by-Step Installation Without Wall Damage
The pressure-mount design makes installation straightforward, but getting the fit right is what keeps the gate stable. Follow these steps, and always check the included instructions for any model-specific details.
- Measure the opening: Use a tape measure to find the width of the opening at the top, middle, and bottom. The gate needs to fit snugly, so the narrowest point matters most. The catalog doesn't list the Widespan's exact width range, so verify it against your measurement before buying.
- Position the gate at the right height: Decide where the gate will sit. For a doorway, place it at a height that's convenient for adults to step over but too high for a baby to climb. The catalog doesn't specify a recommended height, so use your judgment based on your child's mobility.
- Adjust the gate to the opening width: Extend the gate to fit the opening. Most pressure gates have a mechanism to widen or narrow the frame. Turn the adjustment knobs or locks until the gate spans the opening without gaps. The catalog mentions the pressure-mount design but not specific adjustment steps—follow the included manual.
- Tighten the pressure locks: Once the gate is in position, tighten the pressure locks on both sides. The goal is a firm grip against the wall or frame without over-tightening, which could damage the surface. You should not be able to wiggle the gate by hand.
- Test the latch and release: Open and close the gate several times using the lever handle. The one-touch release safety lock should engage smoothly. Make sure the gate swings or opens in the direction you want, and that the lock clicks securely when closed.
Protecting Your Walls During Installation
Even though the Widespan gate uses pressure rather than screws, the contact points can still leave marks on delicate surfaces. If your walls are painted or have wallpaper, consider placing thin rubber pads or felt strips between the gate's ends and the wall. These aren't included, but they're a simple way to reduce scuffs.
Another tip: avoid over-tightening the pressure locks. The gate needs to be secure, but cranking it too hard can dent drywall or leave indentations. Tighten just enough to hold the gate firmly in place.
What the Catalog Confirms About This Gate
- Widespan® Extra Wide Baby Gate: The Regalo Widespan Extra Wide Baby Gate (Model #1158) features a pressure-mount design that makes installation easy. This confirms the gate can be installed without drilling, which is the key to avoiding wall damage.

Widespan® Extra Wide Baby Gate - Widespan® Extra Wide Baby Gate: It has an easy-to-use lever handle with a one-touch release safety lock. You'll know what to expect when operating the gate, and you can test that the lock works properly after installation.
- Widespan® Extra Wide Baby Gate: The gate is designed to blend into your home with a sleek, simple look. If aesthetics matter to you, this gate is meant to be less visually intrusive than some bulky alternatives.
What to Check Before You Finish
Before you consider the job done, walk through a quick safety check. First, confirm the gate is level—a tilted gate can put uneven pressure on one side. Second, make sure there are no gaps at the bottom or sides that a small child could squeeze through. Finally, test the latch from both sides to ensure it's easy for adults but not for little hands.
If you're installing the gate at the top of stairs, remember that pressure-mounted gates are generally not recommended for that location because they can be pushed out. The catalog doesn't specify stair use for this model, so if that's your plan, you may want to consider a hardware-mounted option instead.

